|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
F_M-1W & F_N-1W Series 1W, FIXED INPUT, ISOLATED & UNREGULATED SINGLE OUTPUT DC-DC CONVERTER Multi-country patent protection RoHS FEATURES High Efficiency up to 79% 3000VDC Isolation Temperature Range: -40C to+85C No Heatsink Required No External Component Required Internal SMD construction Industry Standard Pinout RoHS Compliance PRODUCT PROGRAM Input Part Number F0303M -1W F0305M/N -1W F0503M/N -1W F0505M/N -1W F0509M/N -1W F0512M/N -1W F0515M/N -1W 5 4.5-5.5 Voltage (VDC) Nominal 3.3 Range 3.0-3.6 Voltage (VDC) 3.3 5 3.3 5 9 12 15 3.3 5 12 10.8-13.2 9 12 15 5 9 24 21.6-26.4 12 15 24 output Current (mA) Min 300 200 300 200 111 83 67 300 200 111 83 67 200 111 83 67 42 Max 30 20 30 20 12 9 7 30 20 12 9 7 20 12 9 7 3 70 73 71 69 76 78 78 74 71 74 78 79 72 77 77 79 78 SIP SIP/DIP SIP/DIP SIP/DIP SIP/DIP SIP/DIP SIP/DIP SIP/DIP SIP/DIP SIP/DIP SIP/DIP SIP/DIP DIP DIP DIP DIP DIP Efficiency (%, Typ) Packge style APPLICATIONS The F_M-1W & F_N-1W Series is specially designed for applications where a group of polar power supplies are isolated from the input power supply in a distributed power supply system on a circuit board. These products apply to: 1) Where the voltage of the input power supply is fixed (voltage variation 10%); 2) Where isolation is necessary between input and output (isolation voltage 3000VDC); 3) Where the regulation of the output voltage and the output ripple noise are not demanding. Such as: purely digital circuits, ordinary low frequency analog circuits, and IGBT power device driving circuits. F1203M/N -1W * F1205M/N -1W F1209M/N -1W F1212M/N -1W F1215M/N -1W F2405N -1W F2409N -1W F2412N -1W * F2415N -1W F2424N -1W * Designing. ISOLATION SPECIFICATIONS Item Isolation voltage Isolation resistance Isolation Capacitance Test conditions Tested for 1 minute and 1 mA max Test at 500VDC Min 3000 1000 60 Typ Max Units VDC M pF MODEL SELECTION F0505N-1W Rated Po wer Pack age Styl e Ou tput Vol tage In pu t Voltage Prod uct Seri es COMMON SPECIFICATIONS Item Storage humidity Operating Temperature Storage Temperature Temp. rise at full load Lead temperature 1.5mm from case for 10 seconds -40 -55 15 Test conditions Min Typ Max 95 85 125 30 300 1 Free air convection Plastic (UL94-V0) 3500 4.3 K hours g S C Units % MORNSUN Science & Technology co.,Ltd. Address: 2th floor 6th building, Hangzhou Industrial District, Guangzhou, China Tel: 86-20-38601850 Fax: 86-20-38601272 http://www.mornsun-power.com Short circuit protection* Cooling Case material MTBF Weight *Supply voltage must be discontinued at the end of short circuit duration. MORNSUN reserves the copyright Specifications subject to change without notice. F_M-1W & F_N-1W A/1-2008 Page 1 of 2 OUTPUT SPECIFICATIONS Item Output power Line regulation For Vin change (3.3V output) of 1% (others output) (3.3V output) (5V output) Load regulation 10% to 100% load (9V output) (12V output) (15V output) (24V output) Output voltage accuracy Temperature drift Ripple& Noise* Switching frequency 100% full load 20MHz Bandwidth Full load, nominal input 100 100 15 10 8.3 6.8 6.3 6.0 Test conditions Min 0.1 Typ Max 1 1.5 1.2 20 15 15 15 15 15 % Units W APPLICATION NOTE Requirement on output load To ensure this module can operate efficiently and reliably, During operation, the minimum output load is not less than 10% of the full load, and that this product should never be operated under no load! If the actual output power is very small, please connect a resistor with proper resistance at the output end in parallel to increase the load, or use our company's products with a lower rated output power. Recommended circuit If you want to further decrease the input/output ripple, an "LC" filtering network may be connected to the input and output ends of the DC/DC converter, see (Figure 1). L L See tolerance envelope graph 0.03 150 %/C mVp-p KHz *Test ripple and noise by "parallel cable" method. See detailed operation instructions at Testing of Power Converter section, application notes. Note: 1. All specifications measured at TA=25C, humidity<75%, nominal input voltage and rated output load unless otherwise specified. 2. See below recommended circuits for more details. Vin Cin +Vo DC DC Cout GND 0V (Figure 1) It should also be noted that the inductance and the frequency of the "LC" filtering network should be staggered with the DC/DC frequency to avoid mutual interference. However, the capacitance of the output filter capacitor must be proper. If the capacitance is too big, a startup problem might arise. For every channel of output, provided the safe and reliable operation is ensured, the recommended capacitance of its filter capacitor sees (Table 1). EXTERNAL CAPACITOR TABLE (Table 1) Single Vout Vin Cin Cout (VC) (VDC) (uF) (uF) TYPICAL CHARACTERISTICS Operating Temp.(oC) 3.3/5 4.7 2.2 1 - 3.3/5 9 12 15/24 10 4.7 2.2 1 OUTLINE DIMENSIONS & PIN CONNECTIONS First An gle Projection FXXXX M-1W FXXXXN-1W 12 24 - It's not recommended to connect any external capacitor in the application field with less than 0.5 watt output. (0.161) Side view 0.50 (0.020) Output Voltage Regulation and Over-voltage Protection Circuit The simplest device for output voltage regulation, over-voltage and over-current protection is a linear voltage regulator with overheat protection that is 10.00(0.394) 6.00(0.236) 1234 Bottom view 1 7 4 5 connected to the input or output end in series (Figure 2). Vin GND Vin REG +Vout DC DC 0V REG RECOMMENDED FOOTPRINT Top view,grid:2.54mm(0.1inch), diameter:1.00mm(0.039inch) +Vout 12 3 4 7 1 5 4 GND DC DC 0V (Figure 2) Overload Protection Under norm al operating conditions, the output circuit of these products has no protection against FOOTPRINT DETAILS Pin 1 2 3 4 Function GND Vin 0V +Vo Pin 1 4 5 7 Function GND Vin +Vo 0V overload. The simplest method is to connect a self-recovery fuse in series at the input end or add a circuit breaker to the circuit. No parallel connection or plug and play. N ote: U nit:mm(inch) Pin secti on:0.50*0.30mm(0.020*0.012inch) Pin secti on tolerances: 0.10mm( 0.004inch) General tolerances: 0.25mm( 0.010i nch) MORNSUN reserves the copyright Specifications subject to change without notice. F_M-1W & F_N-1W A/1-2008 Page 2 of 2 |
Price & Availability of F1205MN-1W |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |